Vehicles
Sections
423 not categorized PORSCHE 997 TURBO GERMANYCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 912 1965-69 (includes uncategorized and accessory items) 99310117054 This is the original stud used in the rennsport and turbo (m64.20 / 60) models. We recommend them for your next engine rebuild. Sold individually. 24 necessary per car.
From $53.90
Make a selection 90012314030 Crush washer typically used for the oil drain plug or the turbo oil reservoir. Sold individually. View/Change Diagram
From $1.00
Make a selection 99610090399 Head gasket set for 996 turbo and GT2 exclusive from FVD ! Set contains all gaskets and seals for an engine overhaul. Please order crankcase gasket set (996 100 996 tuam)separately.
$1,542.20
Make a selection 99919234350EQ Belts undergo a lot of friction and wear. They are cost effective to change and will keep your alternator and engine in good condition. Be sure to follow recommended service and replacement intervals set by Porsche on belts. For 964 c2 tip trans. / 993 tip trans. / 993 c2/ s manual trans. And the 993 turbo. Sold individually. 1 necessary per car.
$11.00
Make a selection BES99715040S2 Quiet version with catalytic bypass and 4x80mm end tips these versions of FVD sport exhaust system is specifically made for increased performance vehicles. Designed for tolerable, pleasant and sonorous sound (especially for the turbo cabriolet). The elimination of the catalysts reduced drastically the back pressure and increases the performance and throttle response to the max! - stainless steel exhaust system - catalytic bypass - 4x80mm end tips - 2 3/4 tubing (70mm) straight through design for maximum power - weighs 39 lbs. (18,1 kg) - made in Germany - dme programming necessary (catalytic adaption) - stock tips will fit. Tech tip: order also repair / gasket set FVD mk9 970 02
$2,928.20
Make a selection BES98215000S The open architecture of this muffler allows for a deeper four-cylinder turbo tone, with plenty of whistling on tap. Coming off throttle from higher rpms exudes a chorus of snarling, gurgling and crackling letting everyone know that this car is not your average 982. + 15 hp & + 12 tq gain. - 2 x 3.5 (90 mm) round tips. - thermal insulation on piping to keep suspension components cool. Withstands up to 2,012 degrees fahrenheit (1,100 degrees celsius). - lower deeper tones than the factory exhaust with far more whistling and gurgling / crackling off throttle. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - no drone in the cabin. - "aero quip" style motorsport muffler connections t...(choose a part on the right to read more)
$2,921.60
Make a selection BES99120040S Take your 991.1 or 991.2 turbo or turbo s to a new level with these muffler bypass pipes. They produce the wildest sound available on the market today and are a perfect upgrade for level 3 or 4 car used on the track. They produce loud, low, deep tones with exaggerated turbo whistling and sinister gurgling and crackling off throttle. By far the best sound you can get out of your turbo, not to mention being able to shoot flames! The only real drawback is the drone in the cabin which we try to minimalize by stepping down the diameter in 3 stages. Features: - + 35 crank hp & + 25 crank torque - 3 tubing (75mm) that tapers down to 2.25" (57mm) to prevent turbo damage. - weighs 7 lbs. (3,1 kg) - German v2a - x5crni1...(choose a part on the right to read more)
$585.20
Make a selection BES99125020SK No need for Porsche sport exhaust (pse) envy with this muffler! This offers weight savings and a far more exotic sound than the pse, all without drone. It is the perfect compromise for you and your loved ones. Rich, deep, turbo motorsport tones with the valves open and soft subtle, completely stock sounds with them closed. Top of the line or range depending on the english and is the best choice for a daily driver. Features: - + 16 crank hp & + 15 crank torque. - weighs 37 lbs. (17 kg) - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - direct bolt on replacement for the factory center muffler. - includes necessary installation hardware. - reduces turbo lag, backpressure and thermal lo...(choose a part on the right to read more)
$4,651.90
Make a selection BES97003040S M&m exhaust develops and produces exhaust pipes, catalysts and complete exhaust systems for street and race exotic and sports cars. m&m exhaust specifically concentrates on maintaining original equipment levels of fitment and finish.
$2,919.40
Make a selection FVD10699703 For 996 turbo and 997 turbo, 996 GT3l. Fits left side. - specially designed for tuned and motorsport vehicles the racing & high performance division of csf build and engineer the most advanced, efficient, and reliable cooling systems in the world. Csf manufacturers radiators with high performance all-aluminum and direct-fit replacement for racecars. The only high performance manufacture to feature this advanced technology. These radiators are stamped to the same geometry of the application's original plastic end radiators. These tanks feature less welding, and are generally considered the strongest tank designs in the industry.
$768.90
Make a selection FVD10699704 For 996 turbo and 997 turbo, 996 GT3l. Fits right side. - specially designed for tuned and motorsport vehicles the racing & high performance division of csf build and engineer the most advanced, efficient, and reliable cooling systems in the world. Csf manufacturers radiators with high performance all-aluminum and direct-fit replacement for racecars. The only high performance manufacture to feature this advanced technology. These radiators are stamped to the same geometry of the application's original plastic end radiators. These tanks feature less welding, and are generally considered the strongest tank designs in the industry.
$768.90
Make a selection FVD95761890MG Factory: engine - v8 twin-turbo capacity - 4806ccm compression ratio - 10,5:1 max. Power - 368kw (500hp) @ 6000rpm max. Torque - 700nm (516 lbf ft) @ 2250-4500rpm max. Speed - 275km/h max. Rpm - 6500rpm acceleration 0-100km/h - 5.1s tuning:* max. Power - 397kw (540hp) @ 6000rpm max. Torque - 780nm (575 lbf ft) @ 3500rpm max. Speed - 280km/h max. Rpm - 6700rpm acceleration 0-100km/h - 5.0s * only with sport exhaust system and sport air filter for 27 + years, FVD-Brombacherhas been setting the standard for Porsche engine building and tuning in Germany. Our deep understanding of the flat 6 Porsche engine naturally led to our engine management software. Over the years we have perfected the art of software tuning, ...(choose a part on the right to read more)
$1,094.50
Make a selection FVD123002ATK This is a factory series borg warner / kkk k27 turbocharger. It is a direct replacement for part # 930 123 003 01 which is currently no longer available from the factory. Send us your turbocharger and we will have it remanufactured by an OEM supplier with exacting standards in Germany. Features: restore factory performance direct replacement please note: kindly contact us for further details on where to send the turbocharger.
$3,285.88
Make a selection F9664120201TTS Only for the turbo s model !
$493.90
Make a selection 99312301452ATK Our k-16 remanufactured turbo is cost competitive and is a direct replacement. Simply send us your original k16 turbochargers and a borg warner / kkk certified technician will remanufacture your turbo. The remanufacturing process includes full inspection to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will replace the turbine wheels, thrust bearings, install new seals, recondition the internals and high speed balance the turbo. This ensures reliability and superior performance for many years to come. The remanufacturing is done on an exchange basis only. You must send us your original k16 turbocharger. After receiving y...(choose a part on the right to read more)
$2,194.50
Make a selection 129T851852 The rh turbo style Porsche wheel is a classic design perfectly suited for any Porsche model. The center section is cast aluminum and finished in a silver paint. The wheels come with standard rh center cap and accept factory Porsche wheel bolts and center caps. The wheels are offered in 17 and 18 with a variety of offsets to fit narrow and wide body Porsche applications. These wheels are made to order and take between 1-3 weeks to deliver. We recommend ordering a set of rh valves, part # 12945281 when ordering this wheel. Please note: if you are installing these on a 928, body work will be required. Sold individually.
$342.10
Make a selection FVD123019ATK Our k24 sport turbocharger is based off the optional k24 turbochargers, found in the GT2 or 993 turbo x50 models. They are remanufactured by borg warner certified technicians in Germany and are a cost-effective solution. The remanufacturing process includes full inspection of the turbocharger to ensure proper operation after the remanufacturing process. We then disassemble, clean and degrease the unit. The compressor wheels are exchanged, lightened and modified for more air flow. All clearances / shaft tolerances are checked for precision to ensure reliability. The end result is 20-30 additional horsepower, in the low and mid rpm range over the factory turbo. The sport turbo also has less lag than a factory k24...(choose a part on the right to read more)
$2,042.70
Make a selection FVD123020ATK Our k24 sport turbocharger is based off the optional k24 turbochargers, found in the GT2 or 993 turbo x50 models. They are remanufactured by borg warner certified technicians in Germany and are a cost-effective solution. The remanufacturing process includes full inspection of the turbocharger to ensure proper operation after the remanufacturing process. We then disassemble, clean and degrease the unit. The compressor wheels are exchanged, lightened and modified for more air flow. All clearances / shaft tolerances are checked for precision to ensure reliability. The end result is 20-30 additional horsepower, in the low and mid rpm range over the factory turbo. The sport turbo also has less lag than a factory k24...(choose a part on the right to read more)
$2,042.70
Make a selection FVD123025ATK K24/26 exchange turbo (only OEM k24 exchange accepted) (up to 700 hp) power is focused on mid and top range rpm's. Facts: - modified compressor housing and backing plate - modified & lightened high flow compressor wheels. - remanufactured by kkk / borg warner certified technicians - free software update for those already running FVD software. FVD brombachers 996 k24/26 race turbos are new units created for those who are looking for ultimate in performance. Power is focused in the mid and top rpm range while keeping turbo lag low. They are completely bolt on and do not require custom headers or special modifications. The factory OEM turbocharger compressor housing is re-profiled and the compressor backing plate...(choose a part on the right to read more)
$2,976.60
Make a selection FVD123047 FVD Brombacher997.2 tt "700 series" upgraded turbos facts: - modified compressor housing for the 3.8 l displacement - modified & lightened billet compressor wheel with 12 blades - 49.55 mm inducer - 68 mm exducer - remanufactured by borg warner certified technicians - shaft tolerances are strictly maintained to ensure durability - free software update for those already running FVD software we start by re-profiling the OEM vtg turbocharger compressor housing and modifying the compressor backing plate. This is done to replace the factory compressor wheel with a larger 12 blade, modified compressor wheel. The larger wheel is also lightened allows the turbo to flow a larger volume of air (more power), and aids i...(choose a part on the right to read more)
$6,413.00
Make a selection FVD123047ATK FVD Brombacher997.2 tt "700 series" upgraded turbos facts: - modified compressor housing for the 3.8 l displacement - modified & lightened billet compressor wheel with 12 blades - 49.55 mm inducer - 68 mm exducer - remanufactured by borg warner certified technicians - shaft tolerances are strictly maintained to ensure durability - free software update for those already running FVD software we start by re-profiling the OEM vtg turbocharger compressor housing and modifying the compressor backing plate. This is done to replace the factory compressor wheel with a larger 12 blade, modified compressor wheel. The larger wheel is also lightened allows the turbo to flow a larger volume of air (more power), and aids i...(choose a part on the right to read more)
$2,634.50
Make a selection FVD50599702MM Front bumper air vent grill an important component for both cooling and aerodynamics. Ensuring the rapid removal of hot air optimized unit cooling front bumper rs grill for all Porsche 997 Carrera models incl. 4s / GTS / GT3 / turbo
$366.30
Make a selection FVD20799601 Scavenging and aeration in the oil pan have been identified as a problem in 996 and Boxster models experiencing high g-forces on the racetrack. This oil pan spacer provides a simple solution. This spacer increases sump capacity by half a liter, providing more reserve to ward off starvation. Thisoil pan spacer clears all factory options including the rear skid plate. Added oil capacities as well as increased oil pan surface area increase oil cooling and engine performance. *oil pan and sump baffle are OEM parts and do not need to be purchased material: 6061 t6 aluminum alloy finish: clear anodized weight: n/a models: Boxster, Boxster s, and 996 models (excludes GT3 and turbocharged models) installation: for best...(choose a part on the right to read more)
$283.80
Make a selection FVD351997TTCS This kit convert's the 997 turbo pccb rotors to steel rotors with yellow pagid pads.( only 5-hole, not central lock ) this system is complete with everything that you need to install. Do not ruin your expensive ceramic brake discs on the track. Get ready for racing with the original and much cheaper Porsche motorsport steel brake discs! What's in the box: 4 x 2-piece brake discs (380 x 34 mm - front / 350 x 28 mm - rear) 4 x wear sensors 2 x set ( front and rear ) brake pad set (pagid yellow - rs29 ) 8 x screws for brake caliper 8 x damping plates technical tip: also order stainless steel brake lines (FVD b96 355 97) and racebrake fluid (012 145 ca).
$6,344.80
Make a selection FVD3522946993R Genuine rear "big red" brake kit which includes 993 turbo calipers, discs, pads, damping plates, warning contacts and hex head mounting bolts. Please note: this kit requires you to reuse your original emergency brake and dust shield.
$3,681.37
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |